Clik here to view.
Rapid Madness Dart Sensor Mod
Zombona, perhaps the NIC's biggest Boomco fan, developed a method to seal the air release holes in Boomco clips (see here) in order to utilize blasters' air output more efficiently. This has been shown...
View ArticleRotofury Disassembly
When disassembling the Rotofury, the priming bar goes through the center of the cylinder and is thicker at both ends than the part that goes inside the cylinder. I am wondering if there is a way to...
View ArticleRecon Spring
While I was working on my latest mod, I took the spring out of a Recon CS-6 along with with entire internal assembly out. I was wondering what the recon spring would fit in, it doesn't do much by...
View ArticleClik here to view.
Retaliator with a Longshot plungertube and sealed breech
Good morning kids. Today I am going to show you how to take the venerable mainstay of the Nerf clip system series of blasters from a small gimmicky pistol to a fire breathing primary ready to...
View ArticleClik here to view.
Sidestrike Newb Mod w/ Crayola Barrel
Sorry this post is rather word-heavy. So I recently began nerf as an actual hobby more than just a passtime. This mod is my first large(ish) scale project. Really i am posting this to say what,...
View ArticleClik here to view.
Demolisher + Abolisher = Demolabolalolisher
Hello Humans, So the Abolisher is a blaster that everyone hates. It is taken for granted how bad it is. It circulated out of stores almost the instant it came out. There isn't a single page on...
View ArticleClik here to view.
Clear Shot/Stormfire: Seal Improvement & Spring Swap
So I had a Clear Shot, and it was terrible (read: Crap Shot). Anyway, I had a spare NF spring, a screwdriver. and a bit of teflon tape. Now it's much better. Supplies Cup to hold your screws Nite...
View ArticleClik here to view.
Nerf Retaliator Mod Help
Hi! I am modifying my Retaliator, and just put in a 5 KG spring and took out the locks. When I tried to put it back together, it doesn't work. In the pictures below, it is not primed. Could someone...
View ArticleReplacement Rough Cut 2x4 Gears
I was wondering if anyone knows where I can get replacement gears for the Rough Cut. I have found the ones made by J0d0cast, but I was wondering if anyone knows where there is a replacement for both...
View ArticleHow to buy parts for Vulcan mods?
Hello! In the past weeks I've been searching info about Vulcan gun. The reason was that it 1) Looks like a coolest ever gun 2) Seems to basically work just as airsoft guns (a motor cocks a spring, than...
View ArticleBroken Nerf Blaster
Hi, I'm new to the forums and was wondering if anyone had any broken or junk nerf guns they didn't want. I need a few parts and love shell but since I don't have any money, i can't affort to take apart...
View ArticleClik here to view.
BIG QUICKLOADER
here's the mod for the BIG QUICKLOADER just twist out the post with needle nose pliers and make a hole where the post was put E-tape on the back end to fit the barrel. the Bigshock its used with has...
View ArticleClik here to view.
Ghetto 12 mags
"Damn Van, back at it again with superstock stuff"Disclaimer : I may use mag and clip interchangeably because you know what I'm talking about I'll teach you how to make these, Intro : I'm surprised...
View ArticleClik here to view.
barrel mod for the bigshock
nerf dart tag pistol barrel mod for the bigshock. I put some old dart foam under the E-tape for ease of removal and cut off the end that contained the AR but leaving the dart post intact. mega bigshock...
View ArticleIntegration Materials
I'm thinking about doing a Modulus+Rayven integration, but am not sure what to use. For example, is epoxy putty just external, or is it like glue? If someone could help, that would be great. Thanks!
View ArticleClik here to view.
noobs strayven overhaul no imrs or lipos
Hi as an intro I should say this is great for younger audiences it is super easy and fun to do. Here is how to make a strayven or any integration the easy way. Note this is just the first part I am not...
View ArticleOMW Unleashed Stage 1 kits for Retaliator and Longshot (cs-12) reliabl
Hi everyone, I was wondering if the Orange Mod Works Unleashed kits for the Longshot cs-12 and Retaliator are easy to install and worth the $18.99 I'm paying for them. I have exprience with modding...
View ArticleClik here to view.
The 'Rapnadomolisher' - SSTS/RS/Demolisher Integration
Base integration here is a 'RaptorStrike' (Nerf Rapidstrike reshelled in a Supersoaker Tornadostrike body), with an additional integrated Demolisher Launcher. This is very much a Work In Progress....
View ArticleOMW Unleashed Stage 1 kits for Retaliator and Longshot (cs-12) reliabl
Hi everyone, I was wondering if the Orange Mod Works Unleashed kits for the Longshot cs-12 and Retaliator are easy to install and worth the $18.99 I'm paying for them. I have exprience with modding...
View ArticleWacky Question
Is there a specific reason why we relocate the dart-holder/barrel-mount to the front? USER WAS WARNED FOR THIS POST
View Article