Stryfe Extended Mag Release
Does any one know if the worker Stryfe extended mag release is any good?
View ArticleClik here to view.
How Do I Remove Erector Set Pieces?
Owner #1 (I'm Owner #3) used Erector Set pieces to reinforce the front section of his Xbow, about a decade ago. Between the nut and bolt rusting together and the Allen head getting stripped, is there...
View ArticleClik here to view.
Elite Rayven Rewiring - help!
Hi, I'm in the process of re wiring my elite rayven. I thought I was finished, but turning it on revealed that the flywheels spin continuously, and the switch stops them. This is the opposite of the...
View ArticleXP180 shaft question
I bought a pair of XP180s off eBay with the little gears on them and thought I'd just pull them off with a pair of pliers. Just looked closer at them and the shafts are shorter than the hellcats. Are...
View ArticleClik here to view.
Rapidstrike FCG Microswitch Bracket
This is probably a little bit of overkill since it's usually only the flywheel switch that needs to be replaced. But I just did not like the tactical sensation of the stock switches so I wanted to see...
View ArticleClik here to view.
Easy titan adapter
I found that the titan can single elites and launch the rockets from this kit. This is technically a mod but it easily opens the possibility to use more ammunition for the titan...
View Articlemotors hot
I am using 2 MTB rhino's in my rayven and after a little bit of testing i noticed the motors got quite hot. Is this normal or is there something wrong? One motor gets hotter than the other, don't know...
View ArticleSomeone please help me screwdrivers are driving me insane!
I have tryed lots of screwdrivers from hardware stores in my areas and non of them will fit they nerf screws with out loosing grip or striping. Please tell me the EXACT screwdriver company name and...
View ArticleReleasing Rayven, Multistage, and RS Flywheel CAD
https://drive.google.com/drive/folders/0BxrLMjUYkm6GdVlacmhQZmRhOFU?usp=sharing Cages should be printed in 2 pieces. The "guide caps" are not strictly necessary, but fully enclose the dart during its...
View ArticleBest method of cutting Nerf plastic
So I have skimmed through this post and plan on reading it through when I have a spare decade to do so, but until then I am looking some tips on cutting up my Nerf blasters (it also seems to be mainly...
View ArticleClik here to view.
For Science!
Usually, when I record a modification, it was successful. This time, though, it failed for me. For science's sake, I have included this experiment. I don't have photos for each step because I usually...
View ArticleClik here to view.
3D Printable Rapidstrike Mod Parts
Hey all, I'd like to share some parts I designed while modding my Rapidstrike. All of these are released Creative Commons 4.0 Noncommercial Attribution Share-Alike. Editable models and installation...
View ArticleClik here to view.
Crossbow Questions
I've been working with my Xbow, and I've got a few questions about it. First, Do I need to have the old spring, which is too long for the plunger tube? When loaded into the blaster, it has 3" of...
View ArticleNitefinder modding
Hi im doing a mod for my Nitefinder im removing AR and im adding a 24 pound spring I got from home depot. Should I reinforce it? and if so how and what to use? Thanks!
View ArticleClik here to view.
Replacement PAS Trigger
Uses an extension spring rather than the original and annoying torsion spring. Made out of 1/4" polycarbonate (which is typically .230" thick). Template: http://captainslug.com/nerf/pastrigger.png...
View ArticleClik here to view.
Dream Ex-1 (Hammershot Modification)
So I was getting a drain blaster, and needed a cylinder for a shotgun barrel and saw my hammer shot. I was sad that I had to take its cylinder; I mean it was a perfectly good hammer shot. So there I...
View Articlehelp with MTB hellcat motor
Hello nerfhaven Recently I accidentally broke off one of the motor tabs on my 180 sized hell cat motors. Is there anything I can do to fix it? or is it trash now? very specifically im talking about...
View ArticleHow much can the stock Stryfe motors take?
I am planning on modding my stryfe, and just cracked it open. I am interested in doing a voltage mod, but don't want to fry my motors. Is there any recommended voltage that provides upgraded velocity...
View ArticleAnyone made a Crossbolt with actual bow arms, and would it be a good
Looking at the Crossbolt design, I think it might be possible. What mods would have to be done to the rest of the blaster?
View Article